The rectangular canopy hood without motor with a large 1.2 m projection is a static commercial stainless steel hood, supplied without a fan, designed to contain smoke, grease and steam above a cooking line, in wall-mounted or island installation. Its generous depth makes it a popular choice for kitchens that generate a lot of smoke.
A large containment volume for effective capture
With a projection of 1.2 m and a front valance of 450 mm, this commercial kitchen hood creates a genuine containment zone above the cooking line. Even during intense or prolonged cooking, steam and fumes stay channelled under the hood rather than spreading into the kitchen: a real benefit for staff comfort and for the air quality of the room.
Technical specifications
| Specification |
Value |
| Projection (depth) |
1.2 m |
| Height |
450 mm |
| Front valance |
450 mm |
| Available lengths |
1 m, 1.5 m, 2 m, 2.5 m, 3 m, 3.5 m, 4 m, 4.5 m, 5 m, 5.5 m, 6 m |
| Filter material |
Stainless steel, baffle filters + blanking plates, stainless steel spacers |
| Grease tray |
With drain plug |
| Weight |
45 kg (package 90 kg) |
| Manufacturing |
France |
| Warranty |
1 year |
Number of filters and outlet according to length
The number of stainless steel baffle filters increases with the length of the hood, and the diameter of the outlet hole to be cut varies accordingly:
- L 1000 mm: 1 baffle filter + 1/2, outlet to be made in Ø 200 or Ø 250 mm
- L 1500 and L 2000 mm: 2 baffle filters + blanking plates, outlet in Ø 250 or Ø 315 mm
- L 2500 mm: 3 baffle filters + blanking plates, outlet in Ø 315 or Ø 355 mm
- L 3000, 3500, 4000 mm: 4 baffle filters + blanking plates, please contact us regarding the ductwork
- L 4500 mm: 5 baffle filters + blanking plates, please contact us regarding the ductwork
- L 5000 mm: 6 baffle filters + blanking plates, please contact us regarding the ductwork
- L 5500 mm: 7 baffle filters + blanking plates, please contact us regarding the ductwork
- L 6000 mm: 8 baffle filters + blanking plates, please contact us regarding the ductwork
The outlet hole is not cut at the factory: it can be made on top, at the back or on one of the sides of the hood, depending on the type of fan chosen. If the fan is installed directly in the hood, it is best positioned centrally, with the outlet in the same location.
Installation and connection
This hood without motor is supplied flat-packed, ready to assemble, with an assembly guide available for download here. It then connects to a double-inlet centrifugal fan, a remote extraction fan box or a roof extract fan, depending on your kitchen configuration. The electrical connection of the fan must be carried out by a qualified professional.
Points to check before ordering
- Hood length suited to the width of your cooking line, allowing an overhang on each side of the equipment (depending on the ductwork and your appliances)
- Location and diameter of the outlet hole to be cut according to the fan chosen (from Ø 200 to Ø 355 mm depending on length)
- Fan or remote fan box compatible with the airflow actually required for your cooking: this airflow depends on the ductwork, elbows, duct length and capture performance
- Available ceiling height for installation, taking into account the 450 mm height of the hood and the clearance above the cooking line
- For lengths from 3 m upwards, please contact us to validate the ductwork sizing
Pairs well with
You can also find our range of hoods without motor, including the make-up air hood, the oven hood and the condensation hood for wash-up areas.